Mathilde ROLAND

En résumé

Entreprises

• Sogeti High Tech - Ingénieur d'étude

  Paris 2014 - maintenant Actuellement en mission chez Aribus Defense and Space.
  Maintien en condition opérationnelle des équipement électriques.

• Astrium - Stage - Projet industriel de fin d'étude

  Blagnac 2014 - 2014 Amélioration continue au sein de l'unité de contrôle des protections thermique.
  Analyse de flux, réorganisation de l'atelier, BPR( Bussiness Process Reengineering), réevaluation charge/capacité de l'unité etc

• EEI - Universidad de Vigo, Spain - Stagiaire

  2013 - 2014 Simulation project with Simio.
  Making a model on Simio about production processes of helicopter tails in composite materials.

• Turbomeca - Continuous Improvment Trainee

  BORDES 2013 - 2013 For this internship I have worked in the Continuous Improvement & Quality Department. This department deal with both Maintenance Repair and Overhaul (MRO) and New Production (NP).
  
  1- Reduction of cost and time in Quote Proposal for Arriel 2 engines:
  I have conducted a Process Map for each module in Quote Proposal. This stage of measure aims to details every steps of an operation. This level of details enable to categorize every action (valuated business non valuated, waste of time). Further thanks to the timing measurement, it also allows the real proportion of these categories.
  Therefore, I have evaluated the cost and understood the reason of each kind of BNVA and Waste of Time, to attempt to find a solution to suppress or reduce it.
  
  2- Make an analysis of team capacity for Arriel 1 and Arriel 2.
  3- Update and improve the “our Ideas” database.
  4- Set up the Notice board for Continuous Improvement.
  5- Implement the new 5s guidelines standards in the whole work floor for MRO..

• AIA (atelier industriel de l'aéronautique) - Internship

  2012 - 2012 About logistics and continuous improvement activity applied to NDT. Defined a database and continued effort on the 5S workshop Non Destructive Test.
  
  I was assigned to the service of Non Destructive Testing (NDT) with two goals. The first concerning logistics and continuous improvement. My efforts was focused on four main points:
  
  - HSE & ergonomics:
  I took care of the Health and Safety aspects. Indeed, it is important that there is in each work area, clear instructions about the wearing of Personal Protective Equipment, safety informations relating to the sector, the use of hazardous materials etc. The goal is to reach the 0 accidents. I mostly worked with the HSE manager on the classification of work orders criticality, reviewed the Risk Analysis Document (RAD) and made proposals for improvement of the usability of some workstations (radiological shooting cabin, treatment of used fluids etc.)
  
  - Support of production:
  Modification, debugging and improving existent Access database (SQL and VBA)
  
  - Quality-at the earliest:
  Implementation of a quality matrix for self-failure detection and implementation of corrective actions.
  
  -5S:
  Improving the standard storage self-service tools in the NDT workshop.
  With implementation of Poka Yoke to ensure traceability tools on each operation.
  Action 5S with sorting, storage, standardization in the preparation offices with the work documentation.
  
  
  My second objective concerned the quality aspect. I conducted a preliminary audit of the special process of control by Eddy Current and proposed several corrective actions.

• HOWMET SAS - Internship

  2011 - 2011 • Trainee at the Process office.
  • Participation in the action of continuous improvement of the company.
  • Kaizen Tests conducted in the molding specialization to find the cause of a fault surface

Formations

• IFMA (Institut Français De Mécanique Avancée)

  Aubiere 2010 - 2014 In addition to my training in mechanics,
  I followed the formation of Industrial Systems and Logistics with courses such as:
  Industrialization and Production Setup
  Modeling, Analysis and Simulation of Production Systems
  Management Quality, Safety and Environment
  Continuous Improvement and Maintenance of Industrial Systems
  

• Lycée Francois Arago

  Perpignan 2007 - 2010 Classes Préparatoires aux grandes écoles PSI
  
  Physique Sciences l'ingénieur - Undergraduate courses to prepare the entry exams to top universities

• Lycée Pablo Picasso

  Perpignan 2004 - 2007 S SI
  
  option sciences de l'ingénieur,
  spécialité physique

Réseau

• Béatrice LABOUCARIÉ

• Benjamin BASCOUL

• Jean-Luc PARIS

• Julien CAUCHY

• Marion PENVERNE

• Tarek KERDOUSSI

• Thierry PARROT

• Tom QUATTRONE

• Zélie THIÉBAULT